broken tx?
Posted: Wed Mar 16, 2016 1:26 pm
I have a x115 that I am having a problem with tx with and without the transverter board. I replaced the transverter so the problem has to be either the x115 itself, the usb interface, or me.
This is the board's codes:
bladeRF> version
bladeRF-cli version: 1.3.1-git-ba561a4
libbladeRF version: 1.5.1-git-ba561a4
Firmware version: 1.9.0
FPGA version: 0.5.0
Whenever I try to tx I get a timeout error. Using various GNURadio scripts including bladeRF_frs.grc, I get something similar to this:
Opening nuand bladeRF with device identifier string: "*:instance=0"
Serial # 417b...8a01
FW v1.9.0 FPGA v0.5.0
gr-osmosdr v0.1.4-72-g164a09fc (0.1.5git) gnuradio v3.7.9.1-69-gefed1fe3
built-in sink types: uhd hackrf bladerf redpitaya file
Opening nuand bladeRF with device identifier string: "*:instance=0"
Serial # 417b...8a01
FW v1.9.0 FPGA v0.5.0
INFO: Audio source arch: alsa
[bladeRF sink] bladerf_sync_tx error: Operation timed out
[bladeRF sink] bladerf_sync_tx error: Operation timed out
[bladeRF sink] bladerf_sync_tx error: Operation timed out
[bladeRF sink] bladerf_sync_tx error: Operation timed out
[bladeRF sink] Consecutive error limit hit. Shutting down.
If I transmit using the cli with 20 seconds of samples at 1msps (below), I will see a signal for ~630 seconds and then it disappears (timeout).
xb 200 enable
xb 200 filter tx custom
xb 200 filter rx custom
set frequency tx 131125000
set samplerate 1000000
set txvga1 -6
set txvga2 25
tx config file=/tmp/2400hz.sc16q11 format=bin
tx start
I am confused as to the problem. Bad hardware?
This is the board's codes:
bladeRF> version
bladeRF-cli version: 1.3.1-git-ba561a4
libbladeRF version: 1.5.1-git-ba561a4
Firmware version: 1.9.0
FPGA version: 0.5.0
Whenever I try to tx I get a timeout error. Using various GNURadio scripts including bladeRF_frs.grc, I get something similar to this:
Opening nuand bladeRF with device identifier string: "*:instance=0"
Serial # 417b...8a01
FW v1.9.0 FPGA v0.5.0
gr-osmosdr v0.1.4-72-g164a09fc (0.1.5git) gnuradio v3.7.9.1-69-gefed1fe3
built-in sink types: uhd hackrf bladerf redpitaya file
Opening nuand bladeRF with device identifier string: "*:instance=0"
Serial # 417b...8a01
FW v1.9.0 FPGA v0.5.0
INFO: Audio source arch: alsa
[bladeRF sink] bladerf_sync_tx error: Operation timed out
[bladeRF sink] bladerf_sync_tx error: Operation timed out
[bladeRF sink] bladerf_sync_tx error: Operation timed out
[bladeRF sink] bladerf_sync_tx error: Operation timed out
[bladeRF sink] Consecutive error limit hit. Shutting down.
If I transmit using the cli with 20 seconds of samples at 1msps (below), I will see a signal for ~630 seconds and then it disappears (timeout).
xb 200 enable
xb 200 filter tx custom
xb 200 filter rx custom
set frequency tx 131125000
set samplerate 1000000
set txvga1 -6
set txvga2 25
tx config file=/tmp/2400hz.sc16q11 format=bin
tx start
I am confused as to the problem. Bad hardware?